Back to Product
Troubleshooting

Troubleshooting and Diagnostics Guide for KTI01003001E2DI Two-Door Interlock Controller

Field diagnostics on the KTI01003001E2DI two-door interlock controller can be performed systematically using the onboard status LEDs, audible error indicators, and hardware configuration switches. Follow the fault-isolation procedures below to resolve power, sensor feedback, logic latching, and relay switching issues across field terminations on connector blocks CON1 and CON2.

Power Supply and Processing Diagnostics (PWR and HB LEDs)

The controller requires a stable 12V DC input connected directly to CON1 Pin 1 (+Ve Supply) and CON1 Pin 2 (-Ve Supply). If the controller fails to energize, verify incoming adapter voltage using a multimeter across CON1 Pins 1 and 2.

  • PWR LED Off: Indicates lack of primary operating voltage. Check adapter output, external power cabling integrity, and correct polarity at CON1 Pins 1 and 2.
  • PWR LED On but HB (Heartbeat) LED Inactive: The HB indicator confirms active board processing. If HB is unlit or frozen, disconnect secondary peripheral loads from CON1 and CON2 to verify that an external wiring short or ground loop is not collapsing board logic.

Continuous Long Beep Audible Alert (Door Sensor Timeout)

The controller features an integrated supervisory timer that monitors door feedback inputs on CON2. If a door remains physically ajar or the door position sensor fails to signal closure within 2 minutes of an access event, the controller flags an error state via a continuous long beep.

  • Door 1 Sensor Feedback: Inspect magnetic reed switch contacts wired to CON2 Pin 1 (NC) and Pin 2 (COM). Ensure the sensor switch achieves physical closure when Door 1 is shut.
  • Door 2 Sensor Feedback: Inspect magnetic reed switch contacts wired to CON2 Pin 3 (NC) and Pin 4 (COM). Verify mechanical alignment between the door frame reed switch and the door-mounted magnet.
  • Interlock Lockout: While the long beep alarm condition persists, the interlock logic prevents the opposing door from unlocking. To clear the alert, physically close the unsealed door or repair severed sensor wiring so the normally closed (NC) circuit restores continuity to COM.

Both Doors Permanently Unlocked (Emergency Latch State)

Triggering the emergency override input across CON1 Pin 11 (Emergency exit I/P) and Pin 12 (GND) commands both lock relay outputs to release permanently, ensuring fail-safe egress during facility emergencies.

  • Indicator Confirmation: Verify whether LED L5 (Emergency Input) and LED L10 (Emergency Output) are illuminated.
  • Clearing the Latch: The controller maintains emergency release indefinitely and will not automatically revert to normal interlocking mode. Once the external emergency break-glass or push switch on CON1 Pin 11/12 is reset to open-circuit, press the onboard tactile RESET pushbutton switch to restore standard sequential logic.

Input Activation and Lock Relay Diagnostics

If access peripherals or request-to-exit buttons fail to cycle the door locks, evaluate the individual channel LEDs against trigger inputs:

  • Door 1 Inputs: A momentary dry contact between CON1 Pin 3 (Entry I/P) and Pin 4 (GND) should illuminate LED L1. A contact between CON1 Pin 5 (Exit I/P) and Pin 6 (GND) should illuminate LED L2.
  • Door 2 Inputs: A contact between CON1 Pin 7 (Exit I/P) and Pin 8 (GND) should illuminate LED L3. A contact between CON1 Pin 9 (Entry I/P) and Pin 10 (GND) should illuminate LED L4.
  • Relay Output Status: Activating a valid input when the opposite door is fully closed energizes the respective Form C lock relay, illuminated by LED L6 (Lock 1 O/P) or LED L7 (Lock 2 O/P). If the relay activates but the lock does not release, confirm fail-safe locking devices are wired across COM (Pin 6 or 9) and NC (Pin 7 or 10), while fail-secure hardware is wired across COM and NO (Pin 5 or 8).

Lock Output Hold-Time Configuration (DIP Switches 2, 3, and 4)

If doors remain unlocked for an incorrect duration after activation, check the onboard 3-bit DIP switch array. Switches 2, 3, and 4 establish the lock output release timing:

Switch 2Switch 3Switch 4Output Delay Duration
OFFOFFOFF5 Seconds
OFFOFFON5 Seconds
OFFONOFF10 Seconds
OFFONON15 Seconds
ONOFFOFF20 Seconds
ONOFFON25 Seconds
ONONOFF30 Seconds
ONONON35 Seconds