Back to Product
Installation

eSSL FR1200 Installation and RS-485 Integration Guide

The eSSL FR1200 is engineered as a dedicated slave exit reader that interfaces with host access controllers and standalone biometric terminals via an RS-485 serial bus. Because the device functions purely as a biometric capture and RFID reading peripheral, successful installation relies on physical mounting alignment, correct bus polarity, dedicated device addressing via hardware DIP switches, and proper electrical power distribution.

Mullion Mounting and Physical Placement

With external dimensions measuring 48 mm in width, 100 mm in height, and 37 mm in depth, the FR1200 features a compact mullion-style architecture designed for narrow door jambs, surface-mount electrical backboxes, and slim architectural profiles. The casing features an IP65 ingress protection rating, allowing it to withstand dust and moisture in both indoor and outdoor operational environments. Installation teams must ensure the unit operates within its specified temperature range of 0°C to 45°C and relative humidity levels between 20% and 80% (non-condensing).

Mount the reader at an accessible height on the exit side of the secure portal to allow ergonomic thumb and finger placement onto the optical biometric sensor prism. The unit must be secured flush against the mounting surface to protect internal wiring leads and maintain enclosure integrity.

RS-485 Serial Bus Wiring and Signal Termination

Communication between the FR1200 and the central controller operates over standard RS-485 half-duplex differential signaling. Field technicians must maintain correct signal polarity between devices:

  • RS-485 Data Lines: Connect the 485+ line from the master panel directly to the 485+ lead of the FR1200, and connect the 485- line to 485-. Reversing the polarity of these data lines prevents serial synchronization and drops communication with the host.
  • Bus Termination: For extended cable runs approaching the limits of the RS-485 infrastructure, install a 120-ohm terminal resistor across the 485+ and 485- terminals at the furthest end of the bus to suppress line reflections and signal attenuation.
  • Topology: Wire the serial network in a continuous daisy-chain topology; star or tee taps should be avoided to minimize signal reflection and packet corruption.

Power Supply Sourcing and Distance Limits

The FR1200 operates on a regulated 12V DC power input. In idle state, the reader draws a standby current of less than 100 mA, reaching a maximum operational current under 120 mA during active fingerprint capture, card read sequences, and audio buzzer feedback.

When wired to an eSSL inBio controller (such as the inBio 160, inBio 260, or inBio 460/460 Pro), power can be drawn directly from the panel's EXT485 auxiliary power interface, provided the total current load across all attached readers on that bus does not exceed the 500 mA maximum limit. If the cable distance between the master controller and the FR1200 exceeds 100 meters, voltage drop across long wire gauges can degrade reader performance. In all runs exceeding 100 meters, install an independent local 12V DC power supply adjacent to the reader, maintaining a common ground reference with the host communication bus.

Hardware DIP Switch Addressing and Controller Configuration

Every FR1200 connected to an RS-485 bus must possess a unique device identification address. Configure the hardware DIP switches located on the rear of the device before applying 12V DC power:

  • Address Assignment: Set the DIP switches to assign the specific reader address (device number) matching the door identity and entry/exit designated in the controller management software.
  • Bus Collisions: Ensure no two slave readers (such as an entry reader and exit reader on the same controller channel) share identical DIP switch binary values. Conflicting hardware addresses will cause the controller to drop polling communication.
  • Master Compatibility: The configured reader interfaces seamlessly with eSSL standalone terminals (including F18, F19, F22, SF100, and X990) as well as multi-door inBio control panels.

Commissioning and Biometric Template Sync

Because the FR1200 operates strictly as a peripheral reader, fingerprint template storage and cryptographic 1:N or 1:1 biometric matching occur entirely inside the host inBio panel or master standalone terminal. During commissioning, verify successful communication by presenting a registered card or fingerprint: the internal buzzer will sound to confirm status acknowledgment from the host. If an existing reader unit is swapped or replaced during maintenance, re-enrollment of user fingerprints is not required, as credentials remain secured within the host controller database.