Essential Road Safety Products Every Indian Facility Manager Should Stock

Most accidents inside a campus happen on an ordinary day. A truck reverses into a pillar, a bike takes a blind corner too fast, a worker walks into a wet floor nobody marked, or a car rolls into the wall at the end of a basement bay. Facility managers can prevent most of these with a few simple products, if they are in the store when they are needed. This guide covers the KT India range of road safety products for factories, warehouses, hospitals, offices, schools and housing societies: what to keep in stock, where to use it, how to set it up, and what each kind of site needs.

A well-stocked safety store means the cones go out the minute a spill, repair or delivery needs them.
KT India road safety range

Product	Best for	Key details
300 mm HDPE Safety Cone, 750 mm and 1000 mm Rubber Base Cones	Marking hazards, lanes, spills and work zones	Small cones for indoors; 750 and 1000 mm with heavy rubber bases for roads
Cone Connecting Rod and 6 mm Safety Chain	Joining cones into a quick barrier line	2 m PVC rods; rust-proof, UV-resistant plastic chain by the metre
Retractable Traffic Cone Topper and Solar Cone Flasher	Queue lanes and night-time cone lines	Retractable belt for cones; foldable solar flasher visible up to about 500 m
Water Filled Road Barrier and L Type New Jersey Barrier	Diversions, gate lanes and long-term separation	Interlocking barriers; fill with water or sand for weight
Metal Expandable Barrier and Plastic Expandable Barrier	Closing off a lift, pit or repair area in seconds	Folding barriers that open out to block an area
Pioneer PS 3000 Bollard and Spring Bollard	Lane separation and walkway marking	1200 mm bollard with reflective bands; flexible spring bollard that bends back
Caution Tape 80 Micron	Cordoning off spills, digs and wet areas	Bright yellow barricade tape
Rubber Speed Breaker 500x350x50 and 75 mm Speed Breaker with Arrow	Factory roads, gates and parking entries	Bolt-down rubber humps; 20-25 MT load capacity on the 50 mm model
Highway Rumbler Strip and Speed Breaker Installation	Warning drivers before a gate or crossing	Low rumble strips; KTI also offers installation
Rubber Wheel Stopper 600 mm	Parking bays and basements	Reflective rubber stopper so cars stop before the wall
Convex Mirror 60 cm, 80 cm and Quarter Dome Mirror	Blind corners, ramps, gates and aisle junctions	Polycarbonate outdoor mirrors; quarter dome for ceiling corners indoors
3M Road Stud and Solar Stud Yellow	Lane edges, medians and speed breaker approaches	Reflective and solar-lit studs that show the lane at night
Solar Blinker Yellow, Dual Power Blinker with Pole and Solar Flasher 4 LED	Junctions, gates and hazard points at night	Solar flashing lights; 120-LED blinker visible up to about 1000 m
Solar Delineator and Metal Delineator 1000 mm	Road edges, curves and dividers	Solar delineator with about 36 h backup; sturdy 1 m metal post
Reflective Tape 2 Inch	Marking poles, gates, barriers and vehicles	Red and white reflective tape
Pillar Corner Guard D Shape and KTI Wall Guard	Pillars, wall corners and ramps	1000 mm rubber guards with reflective strips
Rechargeable Traffic Baton	Guards directing traffic at gates	Red and green light modes with a built-in torch
Truck Wheel Chock and Dock Bumper D Type	Loading docks and truck bays	Heavy rubber chock against rollback; 1000 mm dock bumper
M.S Parking Post	Reserving a parking bay	Lockable red parking post with two keys

The essential stock list

• Cones and cone accessories. Every site needs a set of 750 mm safety cones, plus connecting rods or safety chain to turn them into a barrier line. Add solar cone flashers for night work.
• Barriers. Expandable barriers close off a pit, lift or repair zone in seconds. Water filled barriers handle diversions and gate lanes for weeks at a time.
• Speed control. Rubber speed breakers at gates and pedestrian crossings, and rumbler strips to warn drivers before them.
• Visibility. Convex mirrors at blind turns, road studs along lane edges, solar blinkers at junctions and reflective tape on poles and gates.
• Protection. Corner guards on pillars, wheel stoppers in parking bays, and dock bumpers at loading bays.
• Quick response. Caution tape, a rechargeable traffic baton for each gate guard, and wheel chocks at the dock.

How to make your site safer, step by step

1. Walk the site with a map. Mark every gate, blind corner, ramp, crossing, loading bay, parking area and pillar that has been hit. Speak to the drivers and guards; they know the near-misses.
2. Separate people and vehicles first. Mark walkways with bollards or spring posts, and use New Jersey barriers where heavy vehicles run close to people.
3. Slow vehicles where it matters. Fit speed breakers 10 to 15 m before gates, crossings and canteen entries, with studs or paint so they are visible at night.
4. Fix the blind spots. Mount a 60 or 80 cm convex mirror at every blind corner and ramp exit, at a height drivers can see from the seat.
5. Make it visible at night. Add solar studs, solar delineators and blinkers where lighting is poor. Solar products need no wiring.
6. Protect what gets hit. Fit corner and wall guards on pillars and ramps, and wheel stoppers in every bay that ends at a wall.
7. Stock the store. Keep cones, tape, an expandable barrier and spare flashers ready, and train the team to use them the moment there is a spill or repair.

Speed breakers, studs and mirrors make the safe speed the natural speed.
Kit by site type

• Factories and warehouses: speed breakers at gates and crossings, convex mirrors at aisle and road junctions, New Jersey or water filled barriers for walkway separation, corner guards on pillars, dock bumpers and wheel chocks at loading bays, and a store of cones and caution tape.
• Hospitals: low speed breakers with arrows at the ambulance and visitor entries, convex mirrors at the basement ramp, wheel stoppers in parking bays, and retractable cone toppers for drop-off queues.
• Offices, malls and IT parks: wheel stoppers, corner guards and quarter dome mirrors in the basement, parking posts for reserved bays, and spring bollards on drop-off lanes.
• Schools and colleges: speed breakers and rumbler strips before the gate, 1000 mm cones and plastic expandable barriers for drop-off and pickup lanes, and a traffic baton for the gate guard.
• Housing societies: speed breakers at the gate and internal roads, convex mirrors at blind turns, reflective tape on gate poles and solar studs along the driveway.
• Construction sites and road works: water filled barriers, 750 and 1000 mm cones with solar flashers, delineators and caution tape.

In parking areas, small fixes like stoppers, guards and mirrors stop the most common knocks.
Keep it working
Walk the site once a month. Replace faded cones and reflective tape, tighten loose speed breaker bolts, clean mirrors and the panels of solar products, and refill or reposition barriers that have moved. Keep a minimum stock in the store: 10 to 20 cones, two expandable barriers, a few rolls of caution tape and some spare flashers. Review the site layout whenever routes, gates or parking change.
Frequently asked questions
Which cone size should I buy?
300 mm cones suit indoor floors and short-term marking. Use 750 mm cones for roads and yards, and 1000 mm cones for highways, large sites and where they must be seen from far away.
Rubber or concrete speed breakers?
Bolt-down rubber speed breakers are quick to install, bright, reflective and easy to move later. They suit factories, campuses and parking areas.
Where should convex mirrors go?
At every blind corner, gate exit, ramp and aisle junction where a driver or forklift cannot see oncoming traffic. Use 80 cm mirrors for wider roads and longer distances.
Do solar blinkers and studs work in the monsoon?
Yes. They charge in daylight, even on cloudy days, and the stored power runs them through the night.
Stock up before the next near-miss. Browse the full range of safety cones and road barriers, or use Enquiry Now on any product page for bulk pricing and a site safety kit tailored to your facility.